Brickcom FD-130AE Manual do Utilizador

Hardware User’s Manual Megapixel Day & Night Fixed Dome Network Camera Quality Service Group Fixed Dome Series

7 Chapter 4 - LED Behavior Function LED Behavior Description Power LED Continuous illumination (Green) Power on Power LED Unit Power off Link LED

8 < Hardware Reset > The Reset Button can be used to reboot the camera or restore it to factory default settings. If the cam

9 Chapter 5 - Installation 5.1 Hardware Installation A. Remove the dome cover from the camera device l. PoE, Power, DIDO, Audio Connection 1) In

10 a. PoE, Power, DIDO, Audio Connection ii. Connect the PoE (1)/ DC 12V (2), DIDO and Audio (3) Cables to their respective terminals. See the nex

11 ll. For SD/SDHC card (*) installation: NOTE – The SD/SDHC card is not included in the product package and needs to be purchased separately.

12 4) Mount the camera on the wall and position to two screw slots over the plastic anchors. Insert the screams into the holes and use the screw

13 C. For ceiling installation: The user needs the two screws which are included in the product package and a screwdriver. Mount the camera o

14 ii. Release the tilt screw on both side of the device and then rotate the lens to up or down. After completion, tighten the tilt screw. iii.

15 b. How to adjust the view angle and focus range i. Release the view angle controller and then moving the controller bar left or right to adjust

16 5.2 Camera Connection F. Basic Connection (Without PoE) a. Connect the power adaptor to the camera device. b. Connect the camera to the Ethern

Review History: 1. Separate User Manual into HW and SW. 2. Merge FD-300Ap/ FD-130N/ FD-132N/ FD-300A/ FD-302A/ FD-500A/ FD-502A series into

17 5.3 System Requirements Operating System: Microsoft Windows XP Home Edition SP2 Microsoft Windows XP Professional SP2 Computer: IBM PC/AT

18 5.4 Software Installation In this manual, "User" refers to whoever has access to the Network Camera, and "Administrator" refe

19 B. In the Install Shield Wizard dialog box, click <Next> to continue. C. Read the End-User License Agreement and check the option “I acc

20 D. Click <Change> to change the appointed folder where installation and program files will be stored. Click <Next> to conti

21 F. Select the application and click <Finish>. When launching the PC-NVR program, please refer to the PC-NVR user manual.

22 5.3.1 EasyConfig To launch EasyConfig, select EasyConfig from the start menu. If Complete Setup type was used in the software installat

23

24 B. Select either “Simple Mode” or “Professional Mode” to obtain the camera’s IP settings. If “Simple Mode” is selected, EasyConfig will

25 C. There may be many cameras in the local network. Differentiate the cameras using their UPnP name. Double click on the camera from the survey l

26 If <Set IP Address configuration manually> is selected, the following pages will be displayed.

Table of ContentsBefore You Use This Product ... 1 Regulatory In

27 E. If the camera supports the EasyLinkTM function, the following page will be displayed. Otherwise, this page will not be shown. *If desi

28 F. When the IP address settings have been configured, the screen will either display a successful or failed connection message. If the connectio

29 c. If the connection was successful, the user will see the message: “Congratulations. The installation of the camera is complete.”

1 Before You Use This Product In many countries, there are laws prohibiting or restricting the use of surveillance devices. This Network

2 Regulatory Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits

3 Chapter 1 - Package Contents a. Network Camera (Fixed Dome series) b. Terminal Block c. Product CD d. Location Sticker e. Warranty Car

4 Chapter 2 - Fixed Dome Network Camera Overview The FIXED DOME SERIES is a full-featured, 3-axis, fixed-dome, network camera. With a

5 Chapter 3 - Device Appearance Description 1. Below “ Device Appearance Description” is for FD-130Np/ FD-132Np/ FD-300Ap V3/ FD-302Ap/ FD-500Ap/

6 3. Below “ Device Appearance Description” is for FD-501Af-series NOTE 1. SD Card Capacity (*) - The network camera is compatible with